Skip to content

From

21,700₾

Deye SUN-50K-SG01HP3-EU-BM4 Hybrid Inverter
SKU
SUN-50K-SG01HP3-EU-BM4
Brand
Deye
Datasheet (PDF)

Deye SUN-50K-SG01HP3-EU-BM4 Hybrid Inverter

The Deye SUN-50K-SG01HP3-EU-BM4 is a High-Voltage commercial hybrid for 50 kW AC (SG01HP3-BM4) — industrial peak shaving and backup where 30 kW is tight and 80 kW is oversized.

Tech Specs

Deye SUN-50K-SG01HP3-EU-BM4 Hybrid Inverter — Tech Specs
Parameter SUN-50K-SG01HP3-EU-BM4
Battery Input Data
Battery Type LiFePO4
Battery Voltage Range (V) 160-800
Max. Charging/Discharging Current (A) 50+50
Charging Strategy for Li-ion Battery Self-adaption to BMS
Number of Battery Input 2
PV String Input Data
Max. PV Access Power (W) 100000
Max. PV Input Power (W) 80000
Max. PV Input Voltage (V) 1000
Start-up Voltage (V) 180
MPPT Voltage Range (V) 150-850
Rated PV Input Voltage (V) 600
Max. Operating PV Input Current (A) 36+36+36+36
Max. Input Short-Circuit Current (A) 55+55+55+55
No. of MPP Trackers / No. of Strings per MPP Tracker 4/2+2+2+2
AC Input/Output Data
Rated AC Input/Output Active Power (W) 50000
Max. AC Input/Output Apparent Power (VA) 55000
Rated AC Input/Output Current (A) 75.8/72.5
Max. AC Input/Output Current (A) 83.4/79.8
Max. Continuous AC Passthrough (grid to load) (A) 200
Peak Power (off-grid) (W) 1.5 times of rated power,10s
Power Factor Adjustment Range 0.8 leading to 0.8 lagging
Rated Input/Output Voltage 220/380V,230/400V 0.85Un-1.1Un 3L+N+PE
Rated Input/Output Grid Frequency/Range (Hz) 50/45-55, 60/55-65
Total Current Harmonic Distortion THDi <3% (of nominal power)
DC Injection Current <0.5%ln
Efficiency
Max. Efficiency 97.6%
Euro Efficiency 97.0%
MPPT Efficiency >99%
Equipment Protection
Integrated Protections DC Reverse Polarity Protection
AC Output Overcurrent Protection
Thermal Protection
AC Output Overvoltage Protection
AC Output Short Circuit Protection
DC Component Monitoring
Arc Fault Circuit Interrupter (AFCI) (optional)
Anti-islanding Protection
DC Switch
Insulation Impedance Detection
Residual Current Detection
Surge Protection Level TYPE II(DC), TYPE II(AC)
Interface
LCD/LED Display LCD
Communication Interface WIFI, RS485, CAN
Monitor Mode GPRS/WIFI/Bluetooth/4G
General Data
Operating Temperature Range (°C) -40°C to +60°C, >45°C Derating
Permissible Ambient Humidity 0-100%
Permissible Altitude 2000 m
Noise (dB) ≤ 65
Ingress Protection (IP) Rating IP 65
Inverter Topology Non-Isolated
Over Voltage Category OVC II(DC), OVC III(AC)
Cabinet Size (W×H×D mm) 527×894×294 (Excluding Connectors and Brackets)
Weight (kg) 80
Type of Cooling Intelligent Air Cooling
Grid Regulation IEC 61727, IEC 62116, CEI 0-21, EN 50549, NRS 097, RD 140, UNE 217002,
OVE-Richtlinie R25, G99, VDE-AR-N 4105
Safety / EMC Standard IEC/EN 61000-6-1/2/3/4, IEC/EN 62109-1, IEC/EN 62109-2
Key Features (datasheet)
Max. Parallel Units (on-grid and off-grid) 10
Battery Charge/Discharge Time Periods 6

Source: official Deye datasheet for SUN-29.9/30/35/40/50K-SG01HP3-EU-BM3/BM4; values are shown for this model.

The economic advantage of the 200–850+ V architecture is driven by basic electrical principles: higher voltage yields proportionally lower current. In a 50 kW system, an HV setup eliminates the need for massive, expensive 50 mm² copper cabling and heavy busbars required by 51.2 V systems. This translates to a significantly lower Balance of System (BOS) cost and minimized voltage drop over distance, making it the only logical choice for commercial plants requiring 40 kWh to several megawatt-hours of storage.

System integration requires strict adherence to HV protocols. Unlike LV systems, HV energy storage modules (such as Heckman RHFP or HECKMAN HV RHFP) are connected in series. It is absolutely critical that all modules are pre-charged to the exact same State of Charge (SOC) before series stringing to prevent BMS lockout. Communication is established by linking the energy storage string's Master BMS directly to the inverter's BMS port via CAN bus. Grid measurement defaults to CHINT DTSU 666; remote utility points beyond 30 m require Eastron SDM Modbus V2 over RS485 or PLC—Power Line Communication over existing phase conductors avoids trenching new meter cables.

Designed to combat the 0.35 ₾/kWh B2B tariff, this inverter supports aggressive peak shaving, dynamic scheduling via EcoBSS EMS / PowerWallet logic, and 100% unbalanced phase output. Up to 10 units can be paralleled (scaling toward 500 kW AC). Safety is paramount: operating at potentially lethal DC voltages up to 850 V, the system demands commercial-grade DC switchgear, strict AC/DC pathway separation, certified PPE, and documented lockout/tagout procedures during commissioning.

Ideal for

  • ✓ Commercial PV plants and factories requiring 40 kWh+ of scalable storage
  • ✓ Installers designing systems where long DC cable runs make LV setups cost-prohibitive
  • ✓ Facilities utilizing dynamic tariffs (PowerWallet) for automated peak shaving

Technical FAQ

Why choose a 200–850+ V HV system over a 51.2 V LV system for a 50 kW project?
Economics and efficiency. HV systems use much thinner, cheaper cables due to lower DC current. They also suffer from fewer thermal losses during DC-to-AC conversion, improving overall system efficiency. For projects requiring over 40 kWh of storage, HV typically delivers a faster ROI on installed cost—not just on electricity savings.
What are the strict rules for connecting HV energy storage modules?
HV modules are connected in series, observing strict polarity. Before physical connection, every single module MUST be balanced to the exact same State of Charge (SOC). Connecting unbalanced modules will cause the BMS to trigger protective faults and delay commissioning.
What safety precautions are necessary for an 850 V DC system?
Unlike 51.2 V systems, 850 V DC is lethal. Installation requires specialized PPE, dedicated high-voltage DC breakers, and strict adherence to commercial electrical codes to prevent arc faults and ensure personnel safety during maintenance.
Can I use standard low-voltage LiFePO₄ energy storage units with this inverter?
No. This inverter is strictly compatible only with High-Voltage energy storage racks (Heckman RHFP HV series) designed to operate within the 200–850+ V range.
← Back to catalog: Inverters

Field notes from Inversol Academy for the codes you are most likely to meet with this equipment.

All Deye error codes →

Nearby power classes and matching LiFePO4 from Tbilisi stock — compare before you quote.

Engineering notes that help you size and choose this product.